STAINLESS STEEL
I now have a few Stainless Steel Cabinets. These are designed as electrical control cabinets as they have a stainless steel outer skin with stainless component plate on the inside with 4 retaining nuts for component plate. But they can have numerous uses.
The door has a lift and twist handle with locking and two keys. There is also a moisture reduction water proof seal fitted to the door. There are also two pre drilled 32mm holes with grommets supplied as blanking should they not be required.
External size 30cm x 25cm x 15cm. (Approx 12″ T x 9.75″ W 7.5″ D) Internal component plate 20cmT x 19cmW and about a .25″ Stand off to allow for fix of components to plate. ( Approx 8″ x 7.5″ ) These are idea for small control Panels.
Price £59.96 Plus P&P.
Ferrules
Ferrules
I normally have a good stock of SS Ferrules. Sometimes I get a run on a particular size and stocks get depleted.
Most amateurs can solder so this leads us to the copper or brass/ferrule. The 2″ Stainless Ferrules are £4.00 + p&p each. They need to be welded into position.
Unfortunately, they are of a size that makes them a small parcel when it comes to postage. This is for the UK only.
51mm 1 x 2″ Clamp, 1 x 2″ Gasket, 2 x 2″ Ferrules. £13.00 ( Also termed 2″ most ferrules go by the leg size )
1 x 51m Stainless Steel Ferrule £3.85
2″ SS Ferrules fit 54mm Copper Tube as do the copper ferrules. All 2″ items have a 64mm ferrule flange, the neck size refers to the 2″ Single Ferrule £4.00
2 x 2″ 64mm Ferrules 1 x Clamp 1 x Gasket. £13.85
2″ Ferrule fits 54mm Copper Tube £4.00
2.5″ Fits 67mm Copper Tube Single Ferrule £5.50
Standard 3″ Ferrule. This is the same size as the 3″ 76mm Tube £7.00
3″ Fits 76mm Copper Tube Single Ferrule. Please note that these ferrule have been specially machined to fit inside 76mm Copper Tube. £8.50
4″ Fits 108mm Copper Tube Single Ferrule £9.50
I also have a few 1″ : 25mm Ferrules with 12mm end and 20mm end for welding. I also have clamps &gaskets
1 x 25mm SS Ferrule x 20mm stem. £3.10
1 x 25mm SS Ferrule x 12mm stem. £3.10
I only have a few of the Mini Ferrules
All items are plus P&P
If you are not sure what size you require have a look in the Miscellaneous section. There is a ferrule size chart.
All postage is for the UK. All postage is for the UK. Europe and the Republic of Ireland is International postage and no longer available. However, if items are under 2Kg I can send them with Royal Mail as customs is not such a problem this is still an option for small items.
Safty Valves, Blow Off Valves, Pressure Relief Valve.
Pressure Relief Valves.
There are three valves 1 is 2″ 64mm ferrule size. 1 is 1″ 51mm ferrule size. 1 is 1/2″ BSP or drill your own hole and fit with the nut, washer and O ring supplied.
These valves all have adjustment by unscrewing the top.
2″ 64mm is 0.2MPa = to 29PSI £56.28
1″ 51mm is 0.2 MPa = to 29PSI £48.82 1 only in stock.
1″ 51mm is 0.1MPa = to 14PSI £46.75
1/2″ 15mm is 0.1 MPa = to 14 PSI £29.85
Bulkhead Fitting
51mm Bulkhead Fitting. This is commonly known as a 1” Tri-Clamp fitting. The one-inch handle covers a multitude of sizes. The actual size is 51mm which is the top OD of the tri-clamp part of the fitting.
51 mm covers various sizes mostly known as 1″
The 64mm Bulkhead Fitting again is known as a 2” fitting this probably comes from the base/shaft which is 51mm 2” The tri-clamp OD size is 64mm.
Hope that explains things a bit.
Still not sure? If you are not sure what size you require have a look in the Miscellaneous section. There is a ferrule size chart.
51mm Bulkhead Fitting. £17.00. 51mm is the ferrule ø size.
64mm Bulkhead Fitting £21.00. 64mm is the ferrule Ø size. This fitting is ideal for converting the T500. Pop this on the top and you can fit the standard 2″ 64mm Columns along with any other 64mm ferrule tri-clamp item. The thread length is 18mm.
All postage is for the UK. All postage is for the UK. Europe and the Republic of Ireland is International postage and no longer available. However, if items are under 2Kg I can send them with Royal Mail as customs is not such a problem this is still an option for small items..
Weld in Sight Glass
Flat Sight Glasses. All my flat sight glasses are rated at 6 Bar.
Weld in Sight Glass
2” 3″ & 4″ Weld in Sight Glasses These are perfect to weld into your beer keg as are the threaded type.
The measurement refers to the approx size of pipe that the sight glass fits into. It is the OD of the part to be welded.
2″ Weld in Sight Glass £23.60
3″ Weld in Sight Glass £36.60
4″ Weld in Sight Glass £64.00
All postage is for the UK. Europe and the Republic of Ireland is International postage please ask before you purchase.
Tri Clamp Sight Glass
Tri-Clamp Sight Glass
2” Ferrule Sight Glass
Another very useful item. Again these can be fit with a 2” tri-clamp or they can be welded into place.
2” Tri Clamp Sight Glass £26.50
3″ Tri Clamp Sight Glass £50.00
4″Tri Clamp Sight Glass £70.00
Tower Sight Glass
Tower Sight Glass
Can be used for all sorts of things. Use as is to just see what’s going on, fill with copper mesh, add copper bubble plate, and stack as many as you like.
2″ Tower Sight Glass Glass £52.00
2.5″ Tower Sight Glass £47.00
3″ Tower Sight Glass £79.00
4″ Tower Sight Glass £108.00
IMPORTANT. CARRIERS DO NOT INSURE GLASS ITEMS. ALL GLASSES ARE INSPECTED BEFORE THEY ARE PACKED. IF THE GLASS IS DAMAGED IT WILL BE AT YOUR RISK. BY MAKING A PURCHASE YOU AGREE TO THIS RISK. Spare glasses are available but the same risk applies.
All items plus P&P
Spare Glass.
Spare Glasses fit the threaded type, weld-in type, ferrule type, and Column Tee Section Glasses. All Glasses are 10mm approx thickness.
< 1mm > All glasses are rated at 6 Bar Pressure.
2″ Glass Only £12.00.
3″ Glass Only £13.50
4″ Column Tee Section Glass Only £12.99
4″ Glass Only £15.00.
Round tubular glass for the Tower Sight Glasses. This is the 2″ 2.5″ 3″ and 4″
2″ Tower Glass Only £20.00
2.5″ Tower Glass Only £23.50
3″ Tower Glass Only £26.75
4″ Tower Glass Only £28.80
All postage is for the UK. All postage is for the UK. Europe and the Republic of Ireland are International postage and no longer available. However, if items are under 2Kg I can send them with Royal Mail as customs is not such a problem this is still an option for small items.
Tri Clamps
Tri Clamps
I have/had a good stock of the Stainless Steel Tri Clamps. I also have a few other sizes. Namely 3/4″ 1″ 2.5” 3” and several 4” Clamps.
3/4″ Tri-Clamp. These fit most of the sizes below 1″ £4.55
1″ Tri-Clamp. £4.65 These fit the 1″ tri-clamp fitting. i.e. the 1″ Lever Ball Valve Tap measures 51mm ø.
2” Clamp. £5.86
2.5” Clamp. £7.25
3” Clamp. £8.00
4” Clamp. £9.85
[3/4″ (25mm dia.) Tri Clamps £4.55
Stainless Steel Left Hand Flange.
Stainless Steel Flanges.
Only a few left. They are left thread to fit and right-hand BSP for the item you fit. Again please ask before you buy to make sure the one you want is in stock.
3/4” DN20 £8.80
1” DN25 £10.40
1.5” DN40 £12.40
2” DN50 £14.00
All postage is for the UK. All postage is for the UK. Europe and the Republic of Ireland is International postage and no longer available. However, if items are under 2Kg I can send them with Royal Mail as customs is not such a problem this is still an option for small items.
Keg Top Flange
Keg Top Flange
New in and exclusive to Distilling UK. These were made specially to my specification for all you folks that can’t Tig Weld. That includes me.
Now all you need to do is drill a few holes and cut off the old spigot. This will leave you with a 4″ hole you can get your arm in and in turn, will allow you to drill more holes and fit more items using threaded items. Shorted.
How to. Place the new Keg Top Flange over the existing spigot. Mark all 13 holes. Centre punch each one to make sure the drill does not wander. Important tip. Never use oil to drill stainless steel.
Heat is the Enemy
Use a water spray. Heat is the biggest enemy when working stainless steel. Drill as slowly as possible and you will find any drill bit will work. Providing it is sharp. Spray the water on the area you are drilling if it starts to steam then it is too hot. Oil doesn’t steam it just case-hardens everything. Use the same method if you cut the main hole around the spigot with a jigsaw. Angle grinder or even a Dremel Tool. Best of all a Plasma Cutter.
Flange
The Keg Top Flange will come to you in a kit form meaning the nuts and bolts will be separate. There are two silicone washers, a small one on the inside larger one on the outside between the keg and the flange 13 SS Bolts 13 SS Nuts 26 SS Washers. You can if you prefer fit 6mm SS Rivnut’s in the inner half-moon parts of the flange as they will fit an 8mm hole. You will then need to purchase the necessary bolts and washers. I find it best to have the bolt on the inside of the keg with the thread facing upwards and the nuts on the outside.
4″ Keg Top Flange
A 4″ Flange is by far the best size as it is better for scaling up or down. Most of you will scale down to 2″ or 3″ with a cone adapter this, in turn, helps the vapour concentrate.
Please be careful with the gaskets that are provided as I only have one set per Flange no spares.
Keg Top Flange £69.99+ P&P
( Info )
Postage is for the UK. Europe and the Republic of Ireland are International Postage. Please ask before you purchase. These are heavy so postage is not cheap.
Threaded Plates & Hose Barbs
Threaded Plates & Hose Barbs.
We have a small selection of plates with threads and hose barbs. The majority of the plates 51mm can also be used with 64mm to 51 mm stubby reducers. These are mainly for direct connection to the 1″ 51mm Leaver Valves. They can also be used with the 2″ 64mm valves with the stubby adapter. ( SS = Stainless Steel TC = Tri-Clamp ) All prices are + P&P
51mm SS TC Plate with Female 1/2″ BSP Thread. £4.75
51mm SS TC Plate with Male 1/2″ BSP Thread. £4.70
51mm SS TC Plate with Male 1″ BSP Thread Spanner Fit Stem. £8.00
64mm SS TC Plate with 18mm OD Hose Tail for 18mm ID Hose. £9.00
51mm SS Plate with 25mm Hose Barb. For Hose ID 25mm £9.55
64mm SS Plate with 25mm Hose Barb. For Hose ID 25mm £11.05
64mm Blank Plate with 5mm female through a threaded hole in the centre. £11.25 These can be fitted with the 6mm threaded PID probe with a little fettling as in grinding the end of the probe slightly so it passes through the thread.
Half Inch Male BSP Threaded Hose Barb with 8mm/10mm barb. £5.99
Half Inch Male BSP Threaded Hose Barb with 10mm/12mm barb. £5.99
Distillers Collection Cup with 9mm Hose Tails. 64mm Tri Clamp fitting. Some folks refer to it as a Tri-clamp Reducer x 9,5mm Pagoda and Exhaust Pipe. £25.99 +P&P
All postage is for the UK. All postage is for the UK. Europe and the Republic of Ireland is International postage no longer available. However, if items are under 2Kg I can send them with Royal Mail as customs is not such a problem this is still an option for small items.
Stainless Reducing Bush
Stainless Steel Reducing Bush
Reducing Bush 1-1/4″ x 1″ ( 1.25″ x 1″ )Threaded on the inside and outside with BSP thread. Ideal for the one-inch elements.
Inch and quarter x Inch BSP Reducing Bush 1.25″ x 1″
Sold single as in one bush. £6.50
1-1/4″ BSP Brass Washer £2.85
Stainless Steel Pot Lid Clips
Lid Clips can be fitted with nuts and bolts or rivets.
They are approximately 120mm in length and 23mm handle to 33mm wide spring clip end. Because the clips are suitable to be riveted in as I do with copper rivets they can be fitted with brass or stainless nuts and bolts. Do not use stand metal nuts and bolts.
A very useful item used in conjunction with the Silicone Pot Rim Seal. The lid clips are a good size for making the seal around your pot.
Lid Clips can be fitted with nuts and bolts or rivets.
1 Clip £2.95
2 Clips £5.75
4 Clips £11.45
6 Clips £15.50
8 Clips £20.00
Bulk order please ask.